Home Manufacturers Skil Routers 1827 F 012 182 745

Skil 1827 Parts (F 012 182 745 )

57 Compatible Accessories Available!

Enhance your Skil F 012 182 745 with our range of accessories

Drawings

1 1619X04235

Motor Housing

£8.73

2 1619P08204

Armature

£25.99

3 1619P08304

Field

£21.65

4 1619X04229

Switch Unit

£4.78

5 1619X06143

Power Supply Cord

£6.53

8 1619X06117

Nameplate

£1.90

9 1619X06320

Manufacturer's Nameplate

£1.90

13 2610042699

Deep-groove Ball Bearing

£8.73

14 1619P01511

Ball Bearing

£4.78

22 1619X06072

Electronic Module

£14.75

23 1619X06114

Electronic Module

£3.03

24 2610916621

Tolerance Ring

£2.05

25 1619X00658

Screw

£1.00

26 1619X04240

Insulator

£1.00

27 1619X02496

Fastener

£1.00

28 1619X04236

Lock Plate

£2.33

29 2610932299

Torsion Spring

£1.00

30 2610315386

Screw

£1.00

31 1619X04234

Housing Cover

£3.33

32 1619X04230

Trigger

£1.00

33 1619X04231

Switch Cover

£1.00

34 1619X04198

Cover

£1.00

35 1619X04237

Bearing Housing

£3.36

36 1619X04232

Screw

£1.00

37 1619X02811

Collet Chuck

£7.42 Not Available

38 2610990022

Screw

£1.00

102 1619X05725

Knob

£1.67

104 1619X04253

Screw

£1.00

105 1619X04252

Retaining Snap Ring

£1.00

106 1619X01014

Spring Washer

£1.00

107 1619X04259

Washer

£1.00

108 1619X04249

Shaft

£2.45

109 1619X04710

Adjusting Part

£2.45

110 1619X04711

Cover

£1.00

111 1619X04271

Cover

£1.00

113 1619X04197

Screw

£1.00

114 1619X04199

Handle

£3.36

116 1619X04250

Cover

£1.00

117 1619X04718

Compression Spring

£1.00

118 1619X05118

Lock Bolt

£3.03

119 1619X04251

Locking Lever

£2.05

120 1619X04721

Washer

£1.00

122 1619X04265

Clamping Lever

£3.36

123 1619X04266

Straight Pin

£1.67

124 1619X04268

Bolt

£1.00

126 1619X04269

Hex Nut

£1.00

127 1619X04262

Rod

£2.00

128 1619X04263

Indicator

£1.00

129 1619X04264

Knob

£1.67

130 1619X04261

Label

£1.00

202 1619X04256

Compression Spring

£1.67

203 2610921832

Bellows

£2.00

204 2916650003

Spring Retaining Ring

£1.00

206 2610916624

Compression Spring

£1.00

207 2600590006

Ratchet Cap

£1.00

208 1619X04723

Washer

£1.00

209 1619X04724

Screw

£1.00

210 1619X04274

Stop

£2.78

211 1619X04273

Chip Deflector

£1.67

213 1619X05012

Screw

£1.00

214 1619X04278

Base Plate

£3.36

216 1619X05276

Plain Washer

£1.00

217 1619X06123

Warning Label

£1.90

651 1619X01769

Adjusting Wrench

£3.36

652 1619X03843

Adapter

£4.01

653 1619X05917

Edge Guide

£6.12

810 1619X06229

Carbon-brush Set

£3.99

811 1619X05564

Service Kit

£30.51

812 1619X06322

Service Kit

£21.65

Ref	Part Number	Description	Price
1	1619X04235	Motor Housing	£8.73
2	1619P08204	Armature	£25.99
3	1619P08304	Field	£21.65
4	1619X04229	Switch Unit	£4.78
5	1619X06143	Power Supply Cord	£6.53
8	1619X06117	Nameplate	£1.90
9	1619X06320	Manufacturer's Nameplate	£1.90
13	2610042699	Deep-groove Ball Bearing	£8.73
14	1619P01511	Ball Bearing	£4.78
22	1619X06072	Electronic Module	£14.75
23	1619X06114	Electronic Module	£3.03
24	2610916621	Tolerance Ring	£2.05
25	1619X00658	Screw	£1.00
26	1619X04240	Insulator	£1.00
27	1619X02496	Fastener	£1.00
28	1619X04236	Lock Plate	£2.33
29	2610932299	Torsion Spring	£1.00
30	2610315386	Screw	£1.00
31	1619X04234	Housing Cover	£3.33
32	1619X04230	Trigger	£1.00
33	1619X04231	Switch Cover	£1.00
34	1619X04198	Cover	£1.00
35	1619X04237	Bearing Housing	£3.36
36	1619X04232	Screw	£1.00
37	1619X02811	Collet Chuck	£7.42	Not Available
38	2610990022	Screw	£1.00
102	1619X05725	Knob	£1.67
104	1619X04253	Screw	£1.00
105	1619X04252	Retaining Snap Ring	£1.00
106	1619X01014	Spring Washer	£1.00
107	1619X04259	Washer	£1.00
108	1619X04249	Shaft	£2.45
109	1619X04710	Adjusting Part	£2.45
110	1619X04711	Cover	£1.00
111	1619X04271	Cover	£1.00
113	1619X04197	Screw	£1.00
114	1619X04199	Handle	£3.36
116	1619X04250	Cover	£1.00
117	1619X04718	Compression Spring	£1.00
118	1619X05118	Lock Bolt	£3.03
119	1619X04251	Locking Lever	£2.05
120	1619X04721	Washer	£1.00
122	1619X04265	Clamping Lever	£3.36
123	1619X04266	Straight Pin	£1.67
124	1619X04268	Bolt	£1.00
126	1619X04269	Hex Nut	£1.00
127	1619X04262	Rod	£2.00
128	1619X04263	Indicator	£1.00
129	1619X04264	Knob	£1.67
130	1619X04261	Label	£1.00
202	1619X04256	Compression Spring	£1.67
203	2610921832	Bellows	£2.00
204	2916650003	Spring Retaining Ring	£1.00
206	2610916624	Compression Spring	£1.00
207	2600590006	Ratchet Cap	£1.00
208	1619X04723	Washer	£1.00
209	1619X04724	Screw	£1.00
210	1619X04274	Stop	£2.78
211	1619X04273	Chip Deflector	£1.67
213	1619X05012	Screw	£1.00
214	1619X04278	Base Plate	£3.36
216	1619X05276	Plain Washer	£1.00
217	1619X06123	Warning Label	£1.90
651	1619X01769	Adjusting Wrench	£3.36
652	1619X03843	Adapter	£4.01
653	1619X05917	Edge Guide	£6.12
810	1619X06229	Carbon-brush Set	£3.99
811	1619X05564	Service Kit	£30.51
812	1619X06322	Service Kit	£21.65

Accessories for Skil F 012 182 745

Two flute cutter 3mm diameter - C001AX1/4TC

Solid carbide two flute cutter. 3.0mm diameter X 9.5mm cut for softwood, harwood, MDF, plywood and chipboard.

D=3 mm Cut length=3/8 inch Cut length=9.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 3.2mm diameter - C001BX1/4TC

Solid carbide two flute cutter. 3.2mm diameter X 12.7mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/8 inch D=3.2 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 6.3mm diameter - C007X1/4TC

Two flute cutter 6.3mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 6.3mm diameter - C008X1/4TC

Two flute cutter 6.3mm diameter X 25.4mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=1 inch Cut length=25.4 mm Overall length=68.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 8.0mm diameter - C012AX1/4TC

Two flute cutter 8.0mm diameter X 25.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=8 mm Cut length=25 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 10mm diameter - C016X1/4TC

Two flute cutter 10mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=25/64 inch D=10 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - C019AX1/4TC

Microgranular tungsten tipped two flute Cutter 12.0mm diameter X 19.0mm cut for a perfect finish for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm C=19 mm C=3/4 inch Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - C019X1/4TC

Two flute cutter 12mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C022X1/4TC

Two flute cutter 12.7mm diameter X 31.8mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=1 1/4 inch Cut length=31.8 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 15.0mm diameter - C024AX1/4TC

Two flute cutter 15.0mm diameter X 25mm cut for softwood, harwood, MDF, plywood and chipboard.

D=19/32 inch D=15 mm Cut length=63/64 inch Cut length=25 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 20.0mm diameter - C030AX1/4TC

Two flute cutter 20.0mm diameter X 20mm cut for softwood, harwood, MDF, plywood and chipboard.

D=20 mm Cut length=20 mm Shank Diameter=1/4 inch Includes:

View full description →

Dovetail cutter angle=104 degrees 12.7mm diameter - C041AX1/4TC

TCT dovetail cutter, 104 degrees X 12.7mm diameter X 12.7mm cut for timber, plywood, MDF, chipboard and abrasive plastics.

D=1/2 inch D=12.7 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=61 mm A=104 degrees Shank Diameter=1/4 inch Includes:

View full description →

Self guided chamfer angle=45 degrees x 12.7mm Cut - C049X1/4TC

Self guided chamfer cutter for straight and shaped material. Angle 45 degrees X 32.0mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings

D=32 mm C=1/2 inch C=12.7 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

View full description →

Rounding over 6.3mm radius x 12.7mm cut - C076X1/4TC

Self guided rounding over cutter with 6.3mm radius X 25.4mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings.

D=1 inch D=25.4 mm C=1/2 inch C=12.7 mm B=9.5 mm B2=12.7 mm R=6.3 mm R=1/4 inch Shank Diameter=1/4 inch Includes:

View full description →

Rounding over 9.5mm radius x 15.9mm cut - C078X1/4TC

Self guided rounding over cutter with 9.5mm radius X 31.7mm diameter X 15.9mm cut.

D=31.7 mm Cut length=5/8 inch Cut length=15.9 mm B=9.5 mm B2=12.7 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Self guided trimmer 12.7mm diameter - C116X1/4TC

Self guided trimmer 12.7mm diameter X 25.4mm cut for trimming plastic or plywood overlays.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm B=12.7 mm A=90 degrees Shank Diameter=1/4 inch Includes:

View full description →

Template profile 12.7mm diameter - C121X1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

View full description →

Biscuit jointer set - C152X1/2TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/2 inch Includes:

View full description →

Biscuit jointer set - C152X1/4TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C153DX1/2TC

Two flute cutter 12.7mm diameter X 50.0mm with centre tip for plunge cutting in abrasive metals, softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 inches Cut length=50 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C153X1/2TC

Two flute cutter 12.7mm diameter X 50.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 inches Cut length=50 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C164X1/2TC

Two flute cutter 12.7mm diameter X 63.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 1/2 inches Cut length=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Guided trimmer 6.35mm diameter x 25.4mm - C168X1/4TC

Guided trimmer 6.35mm diameter X 25.4mm cut for trimming pastic or plywood overlays.

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm B=6.35 mm A=90 degrees Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - C172X1/2TC

Two flute cutter 12.0mm diameter X 63.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=2 1/2 inches Cut length=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Aquamac 21 Recesser 54.5mm diameter - C207X1/2TC

Aquamac 21 Recesser 46.3 mm diameter. Comes complete with a guide bearing to reduce setting up time and simplify machining operations.

D=46.3 mm D2=34.3 mm C=10.3mm C2=2.7 mm B=28.6 mm OL=90 mm Shank Diameter=1/2 inch Includes:

View full description →

Intumescent cutter set 10mm x 40mm - C208X1/2TC

Neat cut intumescent cutter set, 40mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=40 mm C=10 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

View full description →

Intumescent cutter set 10mm x 24mm - C209X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=24 mm C=10 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

View full description →

Intumescent cutter set 15mm x 24mm - C220X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 15mm cut for grooves on door frames for intumescent strips.

D=24 mm C=15 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - TR17DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 12.7mm diameter X 50.0mm cut.

D=1/2 inch D=12.7 mm C=50 mm OL=93 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7 diameter 12.7mm diameter - TR17X1/2TC

Two flute cutter for a clean finish. 12.7mm diameter X 50.0mm cut.

D=1/2 inch D=12.7 mm C=50 mm OL=94 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - TR18DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 12.7mm diameter X 63.0mm cut.

D=1/2 inch D=12.7 mm C=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - TR18X1/2TC

Two flute cutter for a clean finish. 12.7mm diameter X 63.0mm cut.

D=1/2 inch D=12.7 mm C=63 mm OL=106 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 15.9mm diameter - TR19X1/4TC

Two flute cutter for a clean finish. 15.9mm diameter X 19.0mm cut.

D=5/8 inch D=15.9 mm C=19 mm OL=60 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 19.1mm diameter - TR20X1/4TC

Two flute cutter for a clean finish. 19.1mm diameter X 25.0mm cut.

D=3/4 inch D=19.1 mm C=25 mm OL=65.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Radius 5mm radius and 18mm diameter - TR21X1/4TC

Radius cutter for edge coves and fluting. 5.0mm radius X 18.0mm cut.

Cut length=18 mm R=5 mm Shank Diameter=1/4 inch Includes:

View full description →

Chamfer V groove cutter angle=45 degrees - TR22X1/4TC

Chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 12.7mm diameter.

D=1/2 inch D=12.7 mm Overall length=53 mm A=45 degrees Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 6.35mm x 12.7 - TR23X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 12.7mm cut

D=1/4 inch D=6.35 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 6.3mm diameter x 25.4 - TR24X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 25.4mm cut

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm Overall length=74.2 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 9.5mm diameter x 12.7 - TR25X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 9.5mm diameter X 12.7mm cut

D=3/8 inch D=9.5 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=63 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 12.7mm diameter x 25.4 - TR26X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=76.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer triple fluted 12.7X25.4 - TR27X1/4TC

Triple flutted bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 12.7mm x50mm - TR28X1/2TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 50.0mm cut

D=1/2 inch D=12.7 mm Cut length=50 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided profiler - TR29X1/4TC

Guided profiler for trimming and profiling timber and man made board. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=70.8 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided profiler - TR30X1/2TC

Guided profiler for trimming and profiling timber and man made board. 19.1mm diameter X 50.0mm cut.

D=3/4 inch D=19.1 mm Cut length=50 mm Overall length=95 mm Shank Diameter=1/2 inch Includes:

View full description →

Guided ovolo round over cutter 6.35mm radius - TR31X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 25.4mm diameter, incudes 12.7mm bearing.

D=1 inch D=25.4 mm B=9.5 mm R=6.3 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided ovolo over 9.5mm radius - TR32X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 31.7mm diameter, incudes 12.7mm bearing.

D=31.7 mm B=9.5 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided chamfer angle=45 degrees x 31.8mm - TR33X1/4TC

Bearing guided chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 31.8mm diameter.

D=1 1/4 inches D=31.8 mm Overall length=62 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

View full description →

Bearing guided rebater 12.7mm - TR34X1/2TC

Bearing guided rebater, includes 3 extra bearings (9.5mm, 15.9mm and 19.1mm)

D=35mm C=12.7mm Shank Diameter=1/2 inch Includes:

View full description →

Biscuit jointer set - TR35X1/2TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/2 inch Includes:

View full description →

Biscuit jointer set - TR35X1/4TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - TR37X1/2TC

Two flute cutter for a clean finish. 12.0mm diameter X 63.0mm cut.

D=12 mm C=54 mm OL=115 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 15mm diameter - TR40DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm OL=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 15mm diameter - TR40DX1/4TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm Shank Diameter=1/4 inch Includes:

View full description →

Intumescent cutter set 10mm x 40mm - TR41X1/2TC

Bearing guided intumescent recesser, 40.0mm diameter X 10.0mm cut.

D=40 mm Cut length=10 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

View full description →

Intumescent cutter set 15mm x 40mm - TR42X1/2TC

Bearing guided intumescent recesser, 40.0mm diameter X 15.0mm cut.

D=40 mm Cut length=15 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

View full description →

Router Cutter - C121BX1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 9.5mm cut.

View full description →

Router Cutter - TR47X1/2TC

Bearing guided roman ogee, by raising the cutter the top is quickly removed. 25.4mm diameter.

View full description →

This model also has 57 accessories available.

Scroll down to view them.

View both spares and accessories