Home Manufacturers Bosch Routers Router 1618 0 601 618 139

Bosch Router 1618 Parts (0 601 618 139)

57 Compatible Accessories Available!

Enhance your Bosch 0 601 618 139 with our range of accessories

1 2610922584

Motor Housing

£27.69

2 2610934199

Field

£82.33

3 2610934197

Armature

£146.50 Not Available

4 2610913918

On-off Switch

£9.05 Not Available

5/2 3601353500

Terminal

£1.00

6 2610994441

Power Supply Cord

£0.00

7 2601035001

Cable Clip

£1.00

9 2610915243

Nameplate

£0.00

13 3600905513

Deep-groove Ball Bearing

£8.73

14 3600905512

Deep-groove Ball Bearing

£4.05

21 2610991373

Insulating Sleeve

£7.76

22 1604477005

Blade Terminal

£2.33

29 2610993582

Nut

£3.60

31 2610941007

Rear Housing Section

£7.76

32 2610991375

Bearing Holder

£4.19

33 1900210115

O-ring

£2.33

34 2610927708

Housing Cover

£5.15

36 2610994107

Reference Plate

£2.51

39 2602026001

Handle

£4.01

40 2610924105

Base

£0.00

41 1613300006

Hex Nut

£1.00

42 2610915060

Clamping Lever

£1.00 Not Available

44 2610991384

Adjusting Shaft

£0.00 Not Available

45 2610991385

Lever

£4.01

46 2610991371

Spring

£2.05

48 2610993576

Adjusting Device

£2.33

49 2610993577

Ring

£1.00

50 2610928164

Cover Plate

£11.37 Not Available

55 2610991389

Chip Deflector

£4.02 Not Available

56 2610991372

Cover

£1.00

61 2603490017

Torx Oval-head Screw

£1.00

62 2610991306

Tapping Screw

£1.00

66 2918660004

Washer

£1.00

70 2610996054

Retaining Snap Ring

£1.00

71 2610994492

Bolt

£1.00

73 2610915161

Screw

£2.33 Not Available

74 2910641120

Oval-head Screw

£1.00

75 2610910566

Tapping Screw

£1.00

77 2910141166

Hex Socket Head Cap Screw

£1.00

85 2610991370

Guide Sleeve

£25.04

101 2910641152

Oval-head Screw

£1.00

102 3604484501

Receptacle

£9.05

103 2610994461

On-off Switch

£0.00

103/2 3603433506

Socket Head Cap Screw

£1.90

104 3601032500

Fastening Clamp

£5.30

105 3600703500

Grommet

£3.36

106 2910611011

Tapping Screw

£1.00 Not Available

107 2910611424

Tapping Screw

£1.00 Not Available

108 2610912760

Cyl Head Tapping Screw

£0.00

150 2610992417

Single-head Eng. Wrench

£11.64

151 2610991388

Single-head Eng. Wrench

£5.91 Not Available

173 2910871122

Countersunk-head Screw

£0.00 Not Available

750 2610906283

Collet Chuck

£21.43

750 2610906287

Collet Chuck

£21.43

750 2610906284

Collet Chuck

£21.43 Not Available

805 3604460514

Power Supply Cord

£13.34

808 2610907632

Nameplate

£0.00

810 3604321514

Carbon-brush Set

£6.56

816 3604336506

Brush Holder

£11.37 Not Available

817 3604652501

Spiral Spring

£3.03

830 2610997132

Handle

£0.00

Ref	Part Number	Description	Price
1	2610922584	Motor Housing	£27.69
2	2610934199	Field	£82.33
3	2610934197	Armature	£146.50	Not Available
4	2610913918	On-off Switch	£9.05	Not Available
5/2	3601353500	Terminal	£1.00
6	2610994441	Power Supply Cord	£0.00	Contact Us
7	2601035001	Cable Clip	£1.00
9	2610915243	Nameplate	£0.00	Contact Us
13	3600905513	Deep-groove Ball Bearing	£8.73
14	3600905512	Deep-groove Ball Bearing	£4.05
21	2610991373	Insulating Sleeve	£7.76
22	1604477005	Blade Terminal	£2.33
29	2610993582	Nut	£3.60
31	2610941007	Rear Housing Section	£7.76
32	2610991375	Bearing Holder	£4.19
33	1900210115	O-ring	£2.33
34	2610927708	Housing Cover	£5.15
36	2610994107	Reference Plate	£2.51
39	2602026001	Handle	£4.01
40	2610924105	Base	£0.00	Contact Us
41	1613300006	Hex Nut	£1.00
42	2610915060	Clamping Lever	£1.00	Not Available
44	2610991384	Adjusting Shaft	£0.00	Not Available
45	2610991385	Lever	£4.01
46	2610991371	Spring	£2.05
48	2610993576	Adjusting Device	£2.33
49	2610993577	Ring	£1.00
50	2610928164	Cover Plate	£11.37	Not Available
55	2610991389	Chip Deflector	£4.02	Not Available
56	2610991372	Cover	£1.00
61	2603490017	Torx Oval-head Screw	£1.00
62	2610991306	Tapping Screw	£1.00
66	2918660004	Washer	£1.00
70	2610996054	Retaining Snap Ring	£1.00
71	2610994492	Bolt	£1.00
73	2610915161	Screw	£2.33	Not Available
74	2910641120	Oval-head Screw	£1.00
75	2610910566	Tapping Screw	£1.00
77	2910141166	Hex Socket Head Cap Screw	£1.00
85	2610991370	Guide Sleeve	£25.04
101	2910641152	Oval-head Screw	£1.00
102	3604484501	Receptacle	£9.05
103	2610994461	On-off Switch	£0.00	Contact Us
103/2	3603433506	Socket Head Cap Screw	£1.90
104	3601032500	Fastening Clamp	£5.30
105	3600703500	Grommet	£3.36
106	2910611011	Tapping Screw	£1.00	Not Available
107	2910611424	Tapping Screw	£1.00	Not Available
108	2610912760	Cyl Head Tapping Screw	£0.00	Contact Us
150	2610992417	Single-head Eng. Wrench	£11.64
151	2610991388	Single-head Eng. Wrench	£5.91	Not Available
173	2910871122	Countersunk-head Screw	£0.00	Not Available
750	2610906283	Collet Chuck	£21.43
750	2610906287	Collet Chuck	£21.43
750	2610906284	Collet Chuck	£21.43	Not Available
805	3604460514	Power Supply Cord	£13.34
808	2610907632	Nameplate	£0.00	Contact Us
810	3604321514	Carbon-brush Set	£6.56
816	3604336506	Brush Holder	£11.37	Not Available
817	3604652501	Spiral Spring	£3.03
830	2610997132	Handle	£0.00	Contact Us

Accessories for Bosch 0 601 618 139

Two flute cutter 3mm diameter - C001AX1/4TC

Solid carbide two flute cutter. 3.0mm diameter X 9.5mm cut for softwood, harwood, MDF, plywood and chipboard.

D=3 mm Cut length=3/8 inch Cut length=9.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 3.2mm diameter - C001BX1/4TC

Solid carbide two flute cutter. 3.2mm diameter X 12.7mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/8 inch D=3.2 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 6.3mm diameter - C007X1/4TC

Two flute cutter 6.3mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 6.3mm diameter - C008X1/4TC

Two flute cutter 6.3mm diameter X 25.4mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/4 inch D=6.3 mm Cut length=1 inch Cut length=25.4 mm Overall length=68.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 8.0mm diameter - C012AX1/4TC

Two flute cutter 8.0mm diameter X 25.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=8 mm Cut length=25 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 10mm diameter - C016X1/4TC

Two flute cutter 10mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=25/64 inch D=10 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - C019AX1/4TC

Microgranular tungsten tipped two flute Cutter 12.0mm diameter X 19.0mm cut for a perfect finish for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm C=19 mm C=3/4 inch Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - C019X1/4TC

Two flute cutter 12mm diameter X 19.1mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=3/4 inch Cut length=19.1 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C022X1/4TC

Two flute cutter 12.7mm diameter X 31.8mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=1 1/4 inch Cut length=31.8 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 15.0mm diameter - C024AX1/4TC

Two flute cutter 15.0mm diameter X 25mm cut for softwood, harwood, MDF, plywood and chipboard.

D=19/32 inch D=15 mm Cut length=63/64 inch Cut length=25 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 20.0mm diameter - C030AX1/4TC

Two flute cutter 20.0mm diameter X 20mm cut for softwood, harwood, MDF, plywood and chipboard.

D=20 mm Cut length=20 mm Shank Diameter=1/4 inch Includes:

View full description →

Dovetail cutter angle=104 degrees 12.7mm diameter - C041AX1/4TC

TCT dovetail cutter, 104 degrees X 12.7mm diameter X 12.7mm cut for timber, plywood, MDF, chipboard and abrasive plastics.

D=1/2 inch D=12.7 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=61 mm A=104 degrees Shank Diameter=1/4 inch Includes:

View full description →

Self guided chamfer angle=45 degrees x 12.7mm Cut - C049X1/4TC

Self guided chamfer cutter for straight and shaped material. Angle 45 degrees X 32.0mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings

D=32 mm C=1/2 inch C=12.7 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

View full description →

Rounding over 6.3mm radius x 12.7mm cut - C076X1/4TC

Self guided rounding over cutter with 6.3mm radius X 25.4mm diameter X 12.7mm cut. Does not require a side fence, supplied with two bearings.

D=1 inch D=25.4 mm C=1/2 inch C=12.7 mm B=9.5 mm B2=12.7 mm R=6.3 mm R=1/4 inch Shank Diameter=1/4 inch Includes:

View full description →

Rounding over 9.5mm radius x 15.9mm cut - C078X1/4TC

Self guided rounding over cutter with 9.5mm radius X 31.7mm diameter X 15.9mm cut.

D=31.7 mm Cut length=5/8 inch Cut length=15.9 mm B=9.5 mm B2=12.7 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Self guided trimmer 12.7mm diameter - C116X1/4TC

Self guided trimmer 12.7mm diameter X 25.4mm cut for trimming plastic or plywood overlays.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm B=12.7 mm A=90 degrees Shank Diameter=1/4 inch Includes:

View full description →

Template profile 12.7mm diameter - C121X1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

View full description →

Biscuit jointer set - C152X1/2TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/2 inch Includes:

View full description →

Biscuit jointer set - C152X1/4TC

Two wing self-guiding TCT cutter ideal for biscuit jointing, 37.2mm diameter X 4.0mm cut. Three ball bearings supplied (12.7mm, 16.0mm and 19.0mm)

D=37.2 mm Cut length=4 mm B=12.7 mm B2=16.0 mm B3=19.0 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C153DX1/2TC

Two flute cutter 12.7mm diameter X 50.0mm with centre tip for plunge cutting in abrasive metals, softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 inches Cut length=50 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C153X1/2TC

Two flute cutter 12.7mm diameter X 50.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 inches Cut length=50 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - C164X1/2TC

Two flute cutter 12.7mm diameter X 63.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=1/2 inch D=12.7 mm Cut length=2 1/2 inches Cut length=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Guided trimmer 6.35mm diameter x 25.4mm - C168X1/4TC

Guided trimmer 6.35mm diameter X 25.4mm cut for trimming pastic or plywood overlays.

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm B=6.35 mm A=90 degrees Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - C172X1/2TC

Two flute cutter 12.0mm diameter X 63.0mm cut for softwood, harwood, MDF, plywood and chipboard.

D=15/32 inch D=12 mm Cut length=2 1/2 inches Cut length=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Aquamac 21 Recesser 54.5mm diameter - C207X1/2TC

Aquamac 21 Recesser 46.3 mm diameter. Comes complete with a guide bearing to reduce setting up time and simplify machining operations.

D=46.3 mm D2=34.3 mm C=10.3mm C2=2.7 mm B=28.6 mm OL=90 mm Shank Diameter=1/2 inch Includes:

View full description →

Intumescent cutter set 10mm x 40mm - C208X1/2TC

Neat cut intumescent cutter set, 40mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=40 mm C=10 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

View full description →

Intumescent cutter set 10mm x 24mm - C209X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 10mm cut for grooves on door frames for intumescent strips.

D=24 mm C=10 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

View full description →

Intumescent cutter set 15mm x 24mm - C220X1/4TC

Neat cut intumescent cutter set, 24mm diameter X 15mm cut for grooves on door frames for intumescent strips.

D=24 mm C=15 mm B=16 mm E=4 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - TR17DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 12.7mm diameter X 50.0mm cut.

D=1/2 inch D=12.7 mm C=50 mm OL=93 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7 diameter 12.7mm diameter - TR17X1/2TC

Two flute cutter for a clean finish. 12.7mm diameter X 50.0mm cut.

D=1/2 inch D=12.7 mm C=50 mm OL=94 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - TR18DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 12.7mm diameter X 63.0mm cut.

D=1/2 inch D=12.7 mm C=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 12.7mm diameter - TR18X1/2TC

Two flute cutter for a clean finish. 12.7mm diameter X 63.0mm cut.

D=1/2 inch D=12.7 mm C=63 mm OL=106 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 15.9mm diameter - TR19X1/4TC

Two flute cutter for a clean finish. 15.9mm diameter X 19.0mm cut.

D=5/8 inch D=15.9 mm C=19 mm OL=60 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 19.1mm diameter - TR20X1/4TC

Two flute cutter for a clean finish. 19.1mm diameter X 25.0mm cut.

D=3/4 inch D=19.1 mm C=25 mm OL=65.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Radius 5mm radius and 18mm diameter - TR21X1/4TC

Radius cutter for edge coves and fluting. 5.0mm radius X 18.0mm cut.

Cut length=18 mm R=5 mm Shank Diameter=1/4 inch Includes:

View full description →

Chamfer V groove cutter angle=45 degrees - TR22X1/4TC

Chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 12.7mm diameter.

D=1/2 inch D=12.7 mm Overall length=53 mm A=45 degrees Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 6.35mm x 12.7 - TR23X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 12.7mm cut

D=1/4 inch D=6.35 mm Cut length=1/2 inch Cut length=12.7 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 6.3mm diameter x 25.4 - TR24X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 6.35mm diameter X 25.4mm cut

D=1/4 inch D=6.35 mm Cut length=1 inch Cut length=25.4 mm Overall length=74.2 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 9.5mm diameter x 12.7 - TR25X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 9.5mm diameter X 12.7mm cut

D=3/8 inch D=9.5 mm Cut length=1/2 inch Cut length=12.7 mm Overall length=63 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 12.7mm diameter x 25.4 - TR26X1/4TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=76.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer triple fluted 12.7X25.4 - TR27X1/4TC

Triple flutted bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 25.4mm cut

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided trimmer 12.7mm x50mm - TR28X1/2TC

Bearing guided trimmer, for trimming and bevelling timber, lipping and plastic laminate edges. 12.7mm diameter X 50.0mm cut

D=1/2 inch D=12.7 mm Cut length=50 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided profiler - TR29X1/4TC

Guided profiler for trimming and profiling timber and man made board. 12.7mm diameter X 25.4mm cut.

D=1/2 inch D=12.7 mm Cut length=1 inch Cut length=25.4 mm Overall length=70.8 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided profiler - TR30X1/2TC

Guided profiler for trimming and profiling timber and man made board. 19.1mm diameter X 50.0mm cut.

D=3/4 inch D=19.1 mm Cut length=50 mm Overall length=95 mm Shank Diameter=1/2 inch Includes:

View full description →

Guided ovolo round over cutter 6.35mm radius - TR31X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 25.4mm diameter, incudes 12.7mm bearing.

D=1 inch D=25.4 mm B=9.5 mm R=6.3 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided ovolo over 9.5mm radius - TR32X1/4TC

Bearing guided ovolo cutter, produces a smooth round over profile. 31.7mm diameter, incudes 12.7mm bearing.

D=31.7 mm B=9.5 mm R=9.5 mm Shank Diameter=1/4 inch Includes:

View full description →

Guided chamfer angle=45 degrees x 31.8mm - TR33X1/4TC

Bearing guided chamfer and V groove cutter, ideal for fast chamfering to remove edge on timber, or creating a decorative edge. 45 degrees X 31.8mm diameter.

D=1 1/4 inches D=31.8 mm Overall length=62 mm B=9.5 mm A=45 degrees Shank Diameter=1/4 inch Includes:

View full description →

Bearing guided rebater 12.7mm - TR34X1/2TC

Bearing guided rebater, includes 3 extra bearings (9.5mm, 15.9mm and 19.1mm)

D=35mm C=12.7mm Shank Diameter=1/2 inch Includes:

View full description →

Biscuit jointer set - TR35X1/2TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/2 inch Includes:

View full description →

Biscuit jointer set - TR35X1/4TC

Bearing guided biscuit jointer set. Enables biscuit jointing with timber, man made fibre and partical board. 37.2mm diameter X 4.0mm cut

D=29/64 inch D=37.2 mm Cut length=4 mm B=12.7 mm Shank Diameter=1/4 inch Includes:

View full description →

Two flute cutter 12mm diameter - TR37X1/2TC

Two flute cutter for a clean finish. 12.0mm diameter X 63.0mm cut.

D=12 mm C=54 mm OL=115 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 15mm diameter - TR40DX1/2TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm OL=63 mm Shank Diameter=1/2 inch Includes:

View full description →

Two flute cutter 15mm diameter - TR40DX1/4TC

Two flute cutter for a clean finish, TCT centre tip for drilling abrasive material. 15.0mm diameter X 25.0mm cut.

D=15 mm C=25 mm Shank Diameter=1/4 inch Includes:

View full description →

Intumescent cutter set 10mm x 40mm - TR41X1/2TC

Bearing guided intumescent recesser, 40.0mm diameter X 10.0mm cut.

D=40 mm Cut length=10 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

View full description →

Intumescent cutter set 15mm x 40mm - TR42X1/2TC

Bearing guided intumescent recesser, 40.0mm diameter X 15.0mm cut.

D=40 mm Cut length=15 mm B=32 mm E=4 mm Shank Diameter=1/2 inch Includes:

View full description →

Router Cutter - C121BX1/4TC

Bearing guided template profile for rebating and trimming only. 12.7mm diameter X 9.5mm cut.

View full description →

Router Cutter - TR47X1/2TC

Bearing guided roman ogee, by raising the cutter the top is quickly removed. 25.4mm diameter.

View full description →

This model also has 57 accessories available.

Scroll down to view them.

View both spares and accessories